PBM – Motor
Management System
Monitoring,
Control and Protection System
, which brings an integral solution to Motor Control Centers. It
consists of a Base unit (PBM-B) and a user interface Display Module (PMB-H).
Base
Module (PBM-B).
Current measurement is
obtained from the motor line through the magnetic module without need of
external current transformers from 0.8 up to 25 amp. Over 25 amp, use external
current transformers (available through us).
Display
Module (PBM-H).
This is an optional
display module with an LCD screen for signaling, control, and set-up. The LED
indicators can be configured and are identified with labels. Menus are
intuitive and direct, making commissioning of the protection system very easy. The
display is used for event and fault report analyzing in case of protection
trips, current measures, frequency, etc., and for adjusting and setting up the
PBM-B module. In addition, a single display can be used in every facility
module, thanks to his capability of plugging-in into different PBM-B modules.
Fanox has redesigned PBM to provide new
functionality and improve its operability, which makes PBM an indispensable
resource for MCCs.
·
Multifunction
·
4 fault reports
·
Self-diagnosis,
installation, monitoring and statistics
·
Test menu
·
Designed for SCADA
applications
·
Commands management
·
Communication software
(PBCom)
·
Protection functions
Protection Functions
·
Overload with thermal
image
·
Overheating protection
(PTC sensor)
·
Phase imbalance or
phase failure
·
Phase sequence
·
JAM detection
·
Locked rotor detection
·
Instantaneous earth
leakage overcurrent
·
Earth leakage inverse
time overcurrent
·
Instantaneous neutral
overcurrent
·
Neutral inverse time
overcurrent
·
Undercurrent
Fault Reports
Four (4) fault reports that include: dates,
measurements, status bits, inputs and outputs.
Self-Diagnostics, Installation, Monitoring, and Statistics
·
Earth toroidal disconnection
monitoring.
·
PTC sensor open
circuit and short circuit detection.
·
Magnetic module
hardware monitoring.
·
Non-volatile memory
stored information coherence.
·
Number of motor
starts.
·
Medium and maximum
current of last start up.
·
Number of faults for the
following functions:
Overload, PTC, JAM, locked rotor and neutral faults.
·
Operating hours
counter.
·
Test menu.
Designed For Scada Applications
RTU Modbus protocol and RS485 communication
Commands Management
·
Start/Stop by 2 or 3
wires, without additional switches of push-buttons
·
Remote Start/Stop,
more efficiency and cost saving.
Communication software
PBCom
The PBCom PC software is used to communicate
with Fanox PBM Motor Protection Relay. Software is designed to gain access to
PBM relay information, to modify the settings, check states and measurements
and to analyze and save events and fault reports using a graphic-friendly user
interface.
The main operations that can be carried out
using the PBCom software are as follows:
·
General data reading:
Complete model, Version, Serial number, etc.
·
States reading
·
Measurements reading
·
Reading and changing
settings
·
Reading fault reports
·
Changing the user
passwords
·
Saving and Loading
settings files
·
Saving fault reports
·
Date-time
synchronization
·
Configuring the
communication parameters
·
Reading and changing
counters
·
Commands for erasing
the thermal image
It will allow the user to prepare all the
settings and relay configurations without having the relay connected to the PC
(offline mode), reducing engineering and commissioning time.
PBCom software uses Modbus protocol, so ports
with this protocol are required to establish the communication.
PBM-B BASE MODULE
Product Code
Range
400V Motor
Aux. Supply
110/230 Vac-dc
24/48 Vac-dc
I
B
(Amp)
HP
KW
17000
17002
0.8 – 6
0.33 – 3
0.25 – 2.2
17001
17003
4 – 25
3 – 15
2.2 – 11
PBM-H HMI DISPLAY MODULE
Product Code
Language
17015
Spanish
17016
French
17017
English
17018
Polish
17019
German
*
Prices include 3-ft cable to connect PBM-B / PBM-H
Equipment with
halogen-free wiring
Fanox
specializes in the design and manufacture of electronic relays for Low and
Medium Voltage applications.
Since its foundation, back in 1992, Fanox
has developed a wide range of products for multiple applications in the low
voltage sector, having designed and launched new products to the market every
year.
ENERGY CARE TECHNOLOGIES LLC.
is distributor of
FANOX products. Contact us
for wholesale pricing.